Posts

Custom Plastic Mold

Custom plastic Mold

plastic molds can be divided into compression molding mold, injection mold, extrusion mold, blow mold hollow products, thermoforming molds depend on press molding method. In addition to the above listed types of plastic mold, there are other forms of plastic mold. Such as the slush mold, reaction injection mold, foam mold, low pressure fiberglass reinforced plastic molding mold. But no matter what a plastic mold of acceptance should meet the following six basic requirements:

  1. The product forming process, the mold structure and production process analysis. Plastic mold tooling service life should be at least 30 million times.
  2. The mold must be designed to complete the structure and processing parts, and assembly requirements and the proposed injection molding process requirements.
  3. No plastic parts appearance quality defects (such as shrinkage, etc.) or die structure (such as sub-surface setting, gate setting, tool life can not be guaranteed and so on).
  4. The appearance of mold: Mold must ensure that the appearance of rust-free, no hit marks, no defects such as module ground defects.
  5. Mold Transportation: Transportation must be installed on the mold clamping piece, packaging solid, rust-proof.
  6. Mold information: delivery, while in the mold, the mold must provide a set of wearing parts and maintenance of reference materials

Below we are talking about one of custom plastic mold is Crate mold which listed in injection mold, specially we should say plastic injection mold

Crate mold-Thw Ways of Crate Mould Maintenance

Choosing the right documentation software may prove essential in helping crate mould makers collaborate while promoting the principles autonomous maintenance. The right software can help companies develop visual, step-by-step process documentation (procedures that include diagrams, color photos and videos), which enables shops to establish a set of standardized instructions for everything from plastic crate mould cleaning and repair to safety procedures.

While incredibly important, maintenance and cleaning are also tedious and require precise attention to detail. No one really gets

excited about doing them. So, in a busy shop where customers demand quick turnarounds, preventative maintenance often gets

pushed to the back burner. After all, it’s a time-consuming job. It takes a careful, patient and knowledgeable hand to

complete the process correctly.

The right software won’t just aid in the documentation, it can also be the foundation of a shop-wide communication system— a way to distribute expertise from master to journeyman. Even when experts are tied up on other tasks,

their insights can still be referenced by less- experienced workers. You don’t need to look over someone’s shoulder to explain exactly the right way to do a job. The system should handle that for you.

If you want to make plastic crate mould from china, please go to our website to know more about this, we are professional plastic mold making in China that could offer you plastic crate mould, automobile mold, car molds, household mold or any other type of plastic molds.

Plastic injection molding Manufacturing

Plastic injection molding Manufacturing

Plastic Molds and Plastic injection molding is one of the most commonly used molding processes used globally. There are many interesting facts regarding plastic injection molding machines. Injection molding machines vary in sizes they can range to a size of table to as large as your whole room as well. Some injection molding machines have the capacity to produce around 200million plastic molds in one year.

The prices of injection molding machines are also very high. A latest technology molding machines can easily cost $750,000. There are also some molding machines which requires no human resource to operate them they are totally automated. Molding machines needs to be operated with lot of safety and precautions because if a person’s gets in between the mold during the production run the person will be completely crushed into half. Plastic injection molding machines also requires a lot of maintenance which mostly depends on the number of hours the machine is operated daily.

In order to produce consistent plastic parts that too at the fastest cycle time possible to reduce injection molding cost, you need to basically produce its parts in the injection molding process, because it helps in designing and building a mold that will help achieve the above target. There are plastic types that need a cold mold whereas there are some that require hotter mold.

You can do the better cooling mold in various ways depending up the type of plastic to reduce cycle time, but there is this common practice that is followed at a large scale for doing the cooling mold is by drilled holes which basically create a circuit consisting of an in port as well as an out port. This practice is suitable for plastic parts which happen to be square or rectangular. They can also be made the most of by using them in the mold plates as per the need.

By using this method, you are potentially saving more money because this method happens to very economical when it comes to installing water into an injection mold. Just as you would do the cooling of the mold, it is advisable that you do the heating mold up to 200°F. In case the plastic you are dealing with, requires some hotter temperature, then you will need to use hot oil in the waterlines.

 

We have shared with you some of the most common options that you find available for doing mold cooling in injection molding. There’s this point which must not be done and should be avoided which is to not let mold size as well as the mold cost cause you to actually clear off the corners on the mold cooling by cutting.

Looking for plastic injection molding manufaturing? you cancome to us now to know more information.

What is DFM-Design For Manufacturing

What is DFM-Design For Manufacturing

Design For Manufacturing ( DFM ) is the the company’s initial idea prior to mold plastic parts design. Its main target is how to design the mold core part of a plan to meet the requirements set plastic parts. Its content is mainly formed of the gate, parting surfaces, core-pulling ideas.

  • gate design: by the Pro / E of Plastic Adviser of the plastic parts were filled gate position and performance analysis, can find the appropriate position into the plastic. Since the gate point is set in the shape of the surface of the plastic parts, the need to minimize traces of pouring, and taking into account its own mold can pull waste drying track, so a point into the plastic.

  • sub-surface: Plastic Housing Knobbie open mode direction is vertical upward, and set draft is of 1 °. Sub-surface plastic parts should be selected in the bottom surface, it is a good mold release and will not affect the appearance of the quality of the plastic parts can also use the gap and core, thimble, etc. into the sub-gap discharge. To facilitate the process, improve accuracy, the child in plastic molded side hook grooves. This allows the shape of the sub-surface of a plane, more convenient
  • pulling mechanism design: careful observation of three-dimensional model of the plastic parts can be found there is a need to use the slider slot for easy mold after molding. It requires the use of angle pin block side parting pulling mechanism.

H 13 mould steel and H 13 die steel mechanical properties

4Cr5MoSiV die steel die steel, referred to as H13, is a kind of air cooling type heat hardening die steel, wCr=5%, the hardenability of $150.m steel is very good, under air cooling can be hardened. H13 die steel temperature has the toughness and wear resistance of high strength, good heat in, under working temperature with thermal fatigue performance, good anti in addition, good oxidation resistance, small distortion of heat treatment. The mechanical properties of Hl3 die steel Higher Hl3 die steel heat resistance and wear resistance, and toughness similar hardenability is good, is a good material for the production of forging die. Due to higher toughness, even in the quenched state also have certain toughness, thermal fatigue resistance is particularly good, so use it for making high speed hammer forging die is very ideal, and sometimes also used for the production of die casting mold, extrusion mold etc.

Plastic Mold  maintenance and repair matters needing attention

Mould repair note:

1 disassembling the mould, avoid bumping and the water spray, mobile tostationary.

2 spray hot die, then spray a small amount of release agent

3 to conduct a comprehensive inspection of the mold and anti rust treatment: carefully wipe dry cavity, core, the top of the water and sundries institutions and for position and other parts, and spray mold antirust agent and butter.

Maintenance of the mold

In the process of plastic mould in continuous work, due to wear, easy to cause themovement of parts in the process of lubricant deterioration, leakage,pressure injury issues such as plastic materials, the need for mold maintenance.

Mold maintenance is generally divided into the daily maintenance and lower die maintenance

Mold maintenance generally include the following aspects:

1 regular derusting (appearance, PL surface, cavity, core etc.)

2 regular re add lubricant (ejection mechanism for etc.)

3 regular replacement of wear parts (rod, bolts etc.)

4 other places that need attention

Die mold maintenance required by the professional maintenance staff will die after removal of the mold cavity of the mold, a thimble test protection professional.

Plastic Mold Manufacturer In China

Plastic Mold Manufacturer In China

plastic mold manufacturer has many other things to look beyond the basic strength, which is mold manufacturing process. This is so very true in the context of business functions and high end operations that require multidimensional talents and approach. In the present global scenario, the need to pace up with the contemporary trends is visibly important as the business proportions and profits are directly connected.

If you are

plastic mold manufacturer

a recent entry into the molding business with manufacturing capabilities, here are the few important aspects that you need to work of developing expertise…

Design & Packaging – your best of the products and solutions are necessary to be packaged to be presented the way your customers would like to see them. You can engage product packaging experts who are more creative in their approach. Many manufacturing companies engage local creative professionals to custom create packages to suit the localized demands and customer expectations.

Market Inputs – Many new players in the market struggle for the want of market inputs because of which they end up losing some of the most lucrative deals. Knowing the market information and working on the best case scenarios is evidently important for any new enterprise.

Online Presence – your website is as important as your legal registrations. Today, most of the product and service related information is displayed on the respective websites of the companies dealing with various products and services. Your website should also have the vital information on the terms of engagement and business conduct by various patrons involving in your business. If you want to know more information regarding the Plastic Mold Manufacturer, then you can  contact us to get price  supportingplastic mold manufacturing

Plastic Mould manufacturing has become one of the popular businesses in China and in the recent years, many companies which undertook mold manufacturing as their primary business have been established in the country. GC mould which is located in Zhejiang in China is established in the year 1992. This Chinese mould maker, with more than 20 years of experience in mold making is exporting both plastic mould as well as plastic mould components for their clients throughout the world. GC mould is offering plastic molding services for more than 500 leading companies in the world. This company is also represented as one of the leading mold china plastic mould supplier. GC mould is using high precision machineries with advanced techniques so they can offer high quality products at affordable prices than any other companies in China.

Chinese Mold Maker

As GC Mould is implementing advanced techniques, the longevity and precision of the product is ensured. The professional managing teams, technical teams, stable and precision machineries and high quality molds at reasonable price paved the way for GC mould to attain this world’s leading position. GC mould is keen on reducing wastage of time, water, energy, space and labors as they could realize low material, power consumption and high efficiency to reduce the price of the plastic mold. This saved price is more helpful for them, to provide the products to the customers at lower prices. The company is using high quality materials for injecting into the plastic injection molds. GC mould uses two different sorts of plastics which includes thermoplastic and thermosetting plastic. This top Chinese Mold maker also got ISO9001 certificate and so each process of plastic mold making are processed with ISO 9001. If you want to know more information regarding the Chinese Mold Maker, please go to our offical website. and send us your RFQ, we will quote you in the next two working days.